Industry Production :: Industrial Production Manufacturing Essays

Industry Production The structure of industrial production and the service industries is characterized by the prevalence of smarkforce, 30% beingll and medium-sized companies (94% and 5.6% according to 100 workers) thoug981 data), employing, however, only 70% of the workforce, 30% being monopolized by large c ompanies (more than 100 workers) though these comprise only 0.4% of the total. This means that companies are widely dispersed over the whole country, obviously with significant location and concentration of industry, and more than half the industrial comp anies operate at little more than workshop level, as is seen by the small workforce in each production unit. On the other hand, the small number of large companies is explained by increased concentration, at that level also indicated by the high number of employees. There is only a limited number of cooperative companies (food sector and the transformation of agricultural products), while large companies tend to become multinational. The presence of companies with foreign capital monopolizing specific commodity secto rs (pharmaceuticals, photographic materials, electronics, cosmetics etc.) is far from rare. One particular kind of development regards medium-sized companies, frequently derivations of small family-run businesses with a specialized production, which as a result of management flexibility have succeeded in reconverting production and using technol ogical innovations which, with increased competitivity, enable them to penetrate international markets, in this way contributing to the consolidation of the Italian image and presence throughout the world. The Industrial Sectors The steel and metalworking industries The country's economic revival in the immediate postwar period was essentially sustained by development and expansion of the basic industries, particularly the steel industry, itself conditioned by the importation of raw materials such as ores, scrap iron and coal. Membership of ECSC enabled the Italian steel industry, which had installed the integral processing cycle, to attain extremely high levels of production thus satisfying increasingly greater domestic demand, such as that of the engineering industry, as well as the export market. Following plant reconversion steel and metal production is now stagnating due to the international economic situation dominated by strong competition from Japanese industries and plastics, leading to overproduction in the principal European countries. The engineering industries Mechanical engineering production is extremely varied and includes companies such as shipbuilding, aerospace, carbuilding etc. with complex work cycles, together with the manufacturers of simple tools. Component manufacturing is also well developed and cl osely allied to companies producing durable goods not easily classified in any one sector (for example, non-metallic materials used in the car industry: rubber, glass, plastics etc). In practice, mechanical engineering with its diversification and multiple relationships with other industries is considered the mainstay of the national productive system also in terms of the large workforce employed (over 2,2

Summary of the Yellow Wallpaper

Summary of â€Å"The Yellow Wallpaper† by Charlotte Gillman In â€Å"The Yellow Wallpaper,† Charlotte Gillman tells a story of a woman, her husband, and their three month stay at a beautiful home with hideous yellow wallpaper in the master bedroom. The story begins with the woman’s complaints to her husband John about his choice to use the room with the yellow wallpaper instead of one with roses on the window being denied because he felt it would be good for her â€Å"nervous condition†.The woman thought that there was something strange about the house but John told her that her feelings were mere nonsense and that she should get plenty of rest during their stay to try and help her condition. He told her that she should also stay away from her love of writing while he is away treating his patients because it would be too stressful for her condition. During John’s frequent absences the woman begins to obsess over the yellow wallpaper, even going as f ar as to stare at it all night. The woman began to hallucinate about a lady being trapped within the wallpaper after dark and creeping around the garden by day.Her husband thought she was getting better when all that was occurring was his wife was going crazy trying not to bother him. The woman spoke of a recurrent spot where the pattern lolls like a broken neck and two bulbous eyes staring at you upside down. By the end of the story the woman barricaded herself in the master bedroom, ripping down wallpaper in a desperate attempt to free the lady that creeps in the garden by day and is trapped in the walls at night. The purpose of the story is to show how both men and women should have a purpose in society.

Definition of Reliability in Research

Reliability is the degree to which a measurement instrument gives the same results each time that it is used, assuming that the underlying thing being measured does not change. Key Takeaways: Reliability If a measurement instrument provides similar results each time it is used (assuming that whatever is being measured stays the same over time), it is said to have high reliability.Good measurement instruments should have both high reliability and high accuracy.Four methods sociologists can use to assess reliability are the test-retest procedure, the alternate forms procedure, the split-halves procedure, and the internal consistency procedure. An Example Imagine that you’re trying to assess the reliability of a thermometer in your home. If the temperature in a room stays the same, a reliable thermometer will always give the same reading. A thermometer that lacks reliability would change even when the temperature does not. Note, however, that the thermometer does not have to be accurate in order to be reliable. It might always register three degrees too high, for example. Its degree of reliability has to do instead with the predictability of its relationship with whatever is being tested. Methods to Assess Reliability In order to assess reliability, the thing being measured must  be measured more than once. For example, if you wanted to measure the length of a sofa to make sure it would fit through a door, you might measure it twice. If you get an identical measurement twice, you can be confident you measured reliably. There are four procedures for assessing the reliability of a test. (Here, the term test refers to a group of statements on a questionnaire, an observers quantitative or qualitative  evaluation, or a combination of the two.) The Test-Retest Procedure Here, the same test is given two or more times. For example, you might create a questionnaire with a set of ten statements to assess confidence. These ten statements are then given to a subject twice at two different times. If the respondent gives similar answers both times, you can assume the questions assessed the subjects answers reliably. One advantage of this method is that only one test needs to be developed for this procedure. However, there are a few downsides of the test-retest procedure. Events might occur between testing times that affect the respondents answers; answers might change over time simply because people change and grow over time; and the subject might adjust to the test the second time around, think more deeply about the questions, and reevaluate their answers. For instance, in the example above, some respondents might have become more confident between the first and second testing session, which would make it more difficult to interpret the results of the test-retest procedure. The Alternate Forms Procedure In the alternate forms procedure (also called parallel forms reliability), two tests are given. For example, you might create two sets of five statements measuring confidence. Subjects would be asked to take each of the five-statement questionnaires. If the person gives similar answers for both tests, you can assume you measured the concept reliably. One advantage is that cueing will be less of a factor because the two tests are different. However, its important to ensure that both alternate versions of the test are indeed measuring the same thing. The Split-Halves Procedure In this procedure, a single test is given once. A grade is assigned to each half separately and grades are compared from each half. For example, you might have one set of ten statements on a questionnaire to assess confidence. Respondents take the test and the questions are then split into two sub-tests of five items each. If the score on the first half mirrors the score on the second half, you can presume that the test measured the concept reliably. On the plus side, history, maturation, and cueing arent at play. However, scores can vary greatly depending on the way in which the test is divided into halves. The Internal Consistency Procedure Here, the same test is administered once, and the score is based upon average similarity of responses. For example, in a ten-statement questionnaire to measure confidence, each response can be seen as a one-statement sub-test. The similarity in responses to each of the ten statements is used to assess reliability. If the respondent doesnt answer all ten statements in a similar way, then one can assume that the test is not reliable. One way that researchers can assess internal consistency is by using statistical software to calculate Cronbach’s alpha. With the internal consistency procedure, history, maturation, and cueing arent a consideration. However, the number of statements in the test can affect the assessment of reliability when assessing it internally.